Everlast TIG Torch Upgrade: Heavy Hitter 17 With 9mm Quick Connect

By MIG/TIG/Stick Welders & Plasma Cutters | USA Weld – HTP ... | Published: 2026-10-31

Category: Buying Guides

Upgrade your Everlast TIG welder with the Heavy Hitter 17 Series. Learn how the 35 Dinse and 9mm quick connect fit your machine, and when a 200A air-cooled torch makes sense.

Quick answer

The Heavy Hitter® 17 Series (200A) is a direct-fit upgrade for many Everlast® TIG welders that use a 35 Dinse power connection and a 9mm quick connect gas fitting. Choose it if you want a flexible, 200A air-cooled torch for general fabrication; skip it if your Everlast has a different connector or you regularly weld above 200A.

Why the connector type decides your upgrade

The Heavy Hitter 17 Series for Everlast is built with a 35 Dinse (1/2 inch OD) adapter for power and a 9mm quick connect gas fitting. That combination matches specific Everlast models—Power MTS/Lightning (all models), Power Tig (all except early 185), Power Pro (all models), and Power Arc 200STL and 280STH. If your machine uses a different power connector or gas fitting, this torch will not attach without an adapter, so verify your setup before ordering.

The 9mm quick connect gas fitting is a push-to-connect style that speeds torch changes, but it only works with a matching male fitting on your machine or gas hose. If your Everlast has a standard 5/8-18 fitting, you will need a different torch or an adapter.

200A air-cooled: capability and limits

The 17 Series is rated at 200A air-cooled, which covers most general TIG work on steel, stainless, and aluminum up to about 1/4 inch with proper technique. Air-cooled torches are simpler and lighter than water-cooled setups, but they heat up faster during long, high-amperage welds. If you routinely run near 200A for extended periods, a water-cooled torch will be more comfortable and consistent.

Flex neck and cable: comfort vs. durability

This torch uses a flexible neck and a CK Worldwide® super flex power cable, which lets you bend the head to reach tight joints and reduces hand fatigue. The trade-off is that flex necks and super flex cables need more care to avoid kinking or over-bending. For production work where the torch is dragged over edges, a rigid neck may last longer.

Decision rules for your Everlast TIG torch upgrade

Check your Everlast model and connector: Look at the power connector on your welder: if it is a 35 Dinse (1/2 inch OD) and the gas outlet is a 9mm quick connect, this torch is a direct fit. If not, you need a different torch or adapter. Confirm both connectors before ordering.
Match amperage to your work: Choose the 200A Heavy Hitter 17 if most of your welding is below 200A and you want an air-cooled torch. If you regularly weld at or above 200A for long sessions, consider a water-cooled torch instead. Air-cooled suits intermittent work; water-cooled suits continuous high-amperage work.
Decide on flex neck vs. rigid: Pick the flex neck for tight or varied joints where you need torch angle flexibility. Choose a rigid neck if you prioritize durability and simpler handling. Flex adds reach but needs careful handling.
Select length based on your workspace: Order the cable length that matches your welding table and machine placement. Longer cables add reach but can be heavier and harder to manage. Measure your typical reach before choosing length.

Product facts

Heavy Hitter® 17 Series (200A) Air-Cooled Torch for Everlast® TIG Welders with 35 dinse and 9mm Quick connect gas fitting: Heavy Hitter® 17 Series (200A) air-cooled torch with 35 Dinse adapter and 9mm quick connect gas fitting. This is a direct-fit option for Everlast welders with those connections, avoiding adapters.
Heavy Hitter® 17 Series (200A) Air-Cooled Torch for Everlast® TIG Welders with 35 dinse and 9mm Quick connect gas fitting

Is this torch right for you?

Best for

Everlast owners with a 35 Dinse power connector and 9mm quick connect gas fitting
General fabrication and repair work up to 200A
Welders who want a flexible, lightweight air-cooled torch

Not for

Everlast models with a different power or gas connector
Continuous welding above 200A
Users who prefer a rigid neck for durability